Misc Stick building pics help

Tips, part lists, and feedback on Misc Stick building pics help.

• RatMasterD219/14/2009

  so how much for one?

• Vokkan5/21/2009

  I believe the unplugged PCB will drain the voltage otherwise.

• mlearned5/15/2009

  Good diagram. Probably going to use this soon.

• souji55/13/2009

  Left a vote on this build

• jtuyen4/26/2009

  If you need an empty case, contact me jtuyen@gmail.com

• GoodFella4/25/2009

  Left a vote on this build

• holo74/25/2009

  Tyvm for the photos. This has been a huge help in dissecting my own pad.

• TheGlow4/19/2009

  I dunno if theres different bb-070 pads out, but from a quick check of touching signals to grounds I could not get get the RB signal to work off the up or left ground. These are my findings so far. Up or left ground, Up, Left Down's ground, Down, Right, LB, A, Y And my LB and RB signals were the upper right solders when looking at each set of 4 solders. the ones marked here were the grounds. X's ground, Back, X, B, RB Starts ground, Start, Guide Looks like it should work with 4 grounds. up and left dont play nice with anybody else.

• jtuyen4/13/2009

  if you need a blank case, reach me jtuyen@gmail.com

• jtuyen4/13/2009

  if you need a blank case, reach me jtuyen@gmail.com

• bencao744/6/2009

  Trigger point is false here. Tough is LB and RB.

• Reale4/3/2009

  Left a vote on this build

• tekkenboy4/3/2009

  wow~! need some of those.. :)

• Markofthewolves4/2/2009

  Left a vote on this build

• Pyre5004/2/2009

  Left a vote on this build

• Pyre5004/2/2009

  Left a vote on this build

• Rike3/24/2009

  what is the purpose of the resistors going to common ground?

• TheEggplantWizard3/17/2009

  I really appreciate this, but where are the right and left bumpers? Also, I can't exactly tell where LT and RT should be grounded either. Thanks again.

• outty3/7/2009

  thanks for uploading this, much appreciated!

• vanRijn3/7/2009

  Nice, but this is his old design. Does anyone have his new 3-piece angled front design blueprints?

• vanRijn3/7/2009

  Left a vote on this build

• Soulsta5r3/1/2009

  I just finished wiring this pad I used the contact straight across from the highlighted point. Everything is working perfect.

• nilpois20973/1/2009

  Left a vote on this build

• fox132/25/2009

  that rocks

• bobo72a2/24/2009

  which one is the ground to wire to for the trigger?

• SubstatiK2/24/2009

  is it necessary to hook up the 5v and 3.3v?

• TMO Gaming2/22/2009

  Left a vote on this build

• inmortal2k92/22/2009

  Left a vote on this build

• Kandorr2/20/2009

  Left a vote on this build

• TMO Gaming11/17/2008

  I didn't make this diagram, did I. ...did I?

• lukass6411/5/2008

  Damn I'd rather stick to the flat plate, it would really save me the trouble of making that concave.

• Zal10/26/2008

  so its just plexi on top then?

• TMO Gaming8/12/2008

  Left a vote on this build

• ShaolinDrunkard8/12/2008

  Left a vote on this build

• Kabal8/11/2008

  Left a vote on this build

• Kabal2/15/2008

  Very informative... ;-)

• shoo2/5/2008

  Left a vote on this build

• ShaolinDrunkard2/4/2008

  Strange that its different than the wired controllers, because I can easily wire up to the triggers on those.

• baf132/4/2008

  Left a vote on this build

• Big Pockets1/25/2008

  That stick is hot! I give an 11!

• Kabal1/18/2008

  Left a vote on this build

• shoo12/26/2007

  Left a vote on this build

• Big Pockets12/14/2007

  Left a vote on this build

• RoBoBOBR12/4/2007

  Left a vote on this build

• Kabal11/29/2007

  that's crazy... cool!